Customize my ride recommendations: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.
In the first place let’s start with some car paint care advices: Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.
If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.
Another popular method for removing car dents out of plastic material involves using two popular household products: a hair dryer and compressed air. Start off by heating the car dent with the hair dryer at its highest temperature, which will expand the plastic of the car. As soon as it’s hot enough, grab the can of compressed air, turn it upside down, and begin spraying that same area. Since the cold air will cause the plastic to contract, the dent will pop out.
Clean the Car. One of the most important things you can do to maintain the exteriors of your car is to wash and shampoo the vehicle regularly. Commercial power washes are also beneficial if you use them every few months. Make sure you keep a good distance between the surface of the car and the pressure jet, so you don’t damage the paint. If you’re unsure you could get it done professionally. Find additional information on Automotive Hail Repair for Colorado Springs Area.
Dents near edges – If a dent of any size is situated near the very edge of a body panel or near a seam, PDR repair may be impossible. The reason for this is that in order to repair a dent using these techniques, you need to access the back side of the dent. The dent has a crease – If there is a sharp crease (like a folded page) in the dent, PDR likely will not work. Older vehicles – If your vehicle is older than 1990 or is a classic car, the odds are good that attempting paintless repair techniques on a dent will damage the paint. This is because the paint quality on older body panels can’t withstand the strain of the repair techniques.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.