Quality affordable Plasma cutters online provider in the UK 2023: Laser beam welding (LBW) uses, as the name suggests, a laser beam as a concentrated heat source to melt metals and create welds. LBW’s high power density results in small heat-affected zones. The spot size of the laser ranges from 0.2 to 13 mm which makes it suitable for welding materials with varying thicknesses, generating a better result than conventional welding process. Laser welding rapidly creates high-quality welds under fine tolerances. The process is generally automated and is used by the automotive, medical and jewellery industries. Although one might think that since oxy-fuel and plasma torches can be used for both welding and cutting, this applies to laser torches as well but this is generally not the case. A standard laser cutting head cannot be used for welding and a laser welding head cannot meet the cutting speeds and quality demanded in most industrial applications.
Important Industrial Gas Cylinder Safety Guidelines to Keep in Mind: Acetylene and oxygen are two industrial gases widely used across various industries. The cylinders accommodating these gases are designed with user’s safety in mind. However, that is not enough to ensure optimum safety in an industrial facility. The following factors will help ensure the same: Understand the Cylinder Properly: A personnel should be familiar with the potential risks and hazards associated with compressed gases while handling them. It is important to understand the properties of the gas filled within such as toxicity, flammability limits, and toxicity – Threshold Limit Value (TLV). Also, it is important to understand the hazards posed by gas at low temperature, high pressure or due to the physical state of the gas – non-liquefied or liquefied, etc. A personnel should read the contents of the label on the cylinder. If the label is missing or not easily readable, then the cylinder should not be used. In addition to improving a personnel’s understanding on oxygen cylinder safety or acetylene cylinder safety, he should be administered a proper plant safety training. Plasma cutters utiilise the 4th state of matter, plasma, to cut through metals such as steel and aluminium. Plasma cutters send an electronic arc through gas (usually compressed air) which then transforms into a plasma arc which is used to cut through the metal. Welding Supplies Direct are distributors for industry leading plasma cutter brands such as Hypertherm, Oxford and Thermacut, as well as many others. We supply plasma cutters for use in CNC applications along with hand cutting plasma cutting machines with built in compressors. CNC plasma cutting is a great method of improving productivity for your fabrication business as it is a much faster method than hand cutting. You can also save on business costs by bringing your profiling and part manufacturing in-house. Speak to one of our sales team today and a turn-key CNC plasma cutting table solution. Discover additional information on plasma cutters.
Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber.
The Hobart Ironman 240 is the updated version to the Ironman 230 that recently has been discontinued. The 240 is a well-reviewed welder that delivers a wide range of power from 30 to 280 amps in a heavy-duty American-made chassis. Hobart equips the Ironman series with its “soft arc” technology for an easier striking, more spatter-free arc. If you are looking to weld aluminum, then like most of their MIG welders, they offer the package with a SpoolRunner 200 spool gun found here, for a few hundred extra bucks. This is a full-sized platform, offering a 15-foot gun connection and able to load a 44-pound spool of wire. Hobart backs the Ironman 240 with a strong five-year limited warranty. The power regulator has 12 notch settings for easy feel when setting the power level with gloves. This power regulator knob seems to be a problem for some users who have reported issues with the knob rotating freely and not changing the power setting. The only downside to this model is that it is unable to run directly off of a generator as it causes problems with the SCR firing timing of the welder. This makes it a bit less portable than some other welders, but nothing you can’t work around. Overall, this is a quality industrial-grade welder which is ideal for farm work which has been compared to Miller 252 – just without the digital screens and a few other features that most people wouldn’t need, but costs a lot less making it excellent value for the money.
Delivery of parts to the welding station in an organized and logical fashion is also a way to reduce welding costs. For example, one company was manufacturing concrete mixing drums. In the fabrication process, the company produced 10 parts for one section, then went on to make 10 parts of another drum section, etc. As pieces came off the line, they were put onto the floor of the shop. When it was time to weld, the operator had to hunt for the pieces needed and sort through them. When the outside welding expert pointed out the amount of time being wasted in this process, the company started to batch each one on a cart. In this way, the pieces needed to weld one drum were stored together and could easily be moved to the welding area. This type of scenario is also true for companies that may outsource parts to a vendor. Though it may cost more to have parts delivered in batches, it may save more in time than having to organize and search through parts to be able to get to the welding stage. How many times each piece is handled in the shop may be an eye-opener to reducing wasted time. To measure such an intangible as this, operators are asked to put a soapstone mark on the piece each time it is touched – some companies are surprised to find out how many times a part is picked up, transported and laid down in the manufacturing process. In the case of one company, moving the welding shop closer to the heat treatment station eliminated four extra times that the part was handled. Basically, handling a part as few times as possible and creating a more efficient production line or work cell will reduce overall costs.
How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.
Power tool pioneers Bosch have been in the game since 1886. They certainly know a thing or two about making one of the best corded angle grinders on the market. I was amazed at the power output and precision you can achieve with the GWS 7-115 angle grinder. Starting off with the look and feel of this grinder, it’s surprisingly slimline and lightweight. It’s certainly easy to hold on to and weighs less than 2 kg. Bosch have made use of a clever 20° angle side handle as well for ultimate precision grinding. Making use of one of Bosch’s brilliant 720 Watt Champion motors, you know this is a tool that’s built to last. Everything is chunky and built for hard work. They’ve included a two-stage safety switch to avoid accidental starts, which is essential for any tool like this. The motor spins a 115 mm cutting disc up to an impressive 11,000 rpm. There’s a relatively low amount of vibration when in use as well. Just 6.5 m/s², which isn’t bad at all for corded grinders. I like the fact that Bosch have flattened the gear head. This reduces the overall size and makes it easy to get into tight spots. If you’re looking for one of the best angle grinders from one of the top names in the business, this is a great choice.
Some advices on welding equipment, MIG and TIG welders, plasma cutters. MIG Welders are extremely popular because they tend to cost less than TIG or Stick welders with comparable power and features, are extremely easy to learn, and can tackle a wide variety of projects. Since the filler metal is fed through the MIG welding torch, welders can use both hands to hold the torch steady rather than using one hand to add filler metal, as in TIG welding. The wire feeder also makes MIG welding up to four times faster. The MIG welding process uses an inert gas to shield the weld and to keep it free from impurities. This makes MIG welding very neat and easy to clean up since there isn’t anything to chip away, which is typical for Stick welding. MIG welding can be used on a wide variety of materials such as aluminum and is also frequently used for automotive work. However, MIG also requires the purchase of shielding gas and generally requires materials that cost more when compared to other methods.
If you’re looking for the best portable weld fume extractor that would be small but powerful and also would come within an affordable price range, then BAOSHISHAN has the perfect device for you! This fume extractor absorbs all sorts of gases and dust generated by soldering and welding. The 1.2m smoking pipe is an added benefit to this fantastic device. Compact Design and Convex Tips. This small and compact machine has a state-of-the-art build quality that ensures high performance. The filters come with metal latches that seal off the fumes and don’t let any fume get out of the device. The pipeline’s sealing and stability are improved by fine convex tips. The machine comes with sturdy wheels that help to move the unit to anywhere you want. Its suction pipe is built with several small pipes which allow it to move around freely.
If value for money is a priority to you, take a look at this drill from Evolution. It is a solid and durable drill that will get the job done for the professional steelworker as well as the weekend handyman. This drill has a 6-inch stroke length and comes with a 0.5-inch chuck and key. The drilling range has a diameter from 7/16? to 1-1/8? and cutting depth of 2 inches unless you change out the chuck to something else. You can place the feeding handle on either side of the drill, depending on what is comfortable to you. The heavy-duty magnet makes it easy to do overhead or horizontal drilling. An integrated cooling system will keep your magnetic drill press from overheating. There are some drawbacks to this drill. It can only turn at the speed of 570 RPM. This works great for when you are drilling steel or aluminum, but this speed is too high for drilling titanium or stainless steel. This drill may also be more primitive than conventional high-end magnetic drill presses.
ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.
GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.
The Lincoln EasyMIG 180 is a well-built welder that’s reliable and will serve a range of light fabrication and workshop projects. Its power input is 230V but it doesn’t have the power of the Hobart 190. This is a great entry level 230V welder that will give you quality welds. It won’t tackle thicker metal but this will do the job for most hobby welders. It’s a great choice for a hobbyist if you have a convenient 230V power outlet.
Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. Read additional info on this website.
MIG welders are divided into transformer and inverter models. Briefly, transformer machines feature only mechanical parts that can adjust the output voltage “sequentially” while the unit is off. The output voltage is not stabilised and may decrease under load. Still, a simple design is the main benefit of transformer welders that facilitate their maintenance. Also, they are often cheaper. Inverter MIG welders are fitted with electronics that allow a smooth voltage adjustment, so it isn’t susceptible to drops and does not fall under load. Of course, power is the main feature of any electric tool. As for MIG welders, their power depends on the maximum amperage, more usually, the output range. This range determines the unit’s field of application. Powerful models can be used on small construction sites or in repair shops, while less powerful models are usually used for private needs. For example, the welders of up to 200A are great for home use; the 300A models are suitable for small repair shops, and if you need a high output and continuous work, consider welders over 300A.
United Kingdom market choice: At just $99, the Goplus is a fantastic value considering what it is equipped to do. In fact, it is the most affordable welder on our list, beating out its competitors by hundreds or even thousands of dollars and putting it in a class of its own. For a budding hobbyist not yet sure if welding is for them, you can’t go wrong with the Goplus. After all, for $99 its welding thickness and the duty cycle is about what one would expect (don’t look to buy this welder if you want it for heavy duty use). The Goplus is light and compact when compared to most other welders. Flux core wire is included. It has four levels of easily adjustable current flow and ten levels of wire speed. The Goplus is able to weld steel and iron at below ¼ inches thickness.